Chevy Truck Rear End Compatibility Chart

I have access to a 1998 tahoe 1500. Mine is a 3/4 ton, the rear end housing has not been changed.

1978-87 Rear Differential - Gm 10 Bolt With 8-12 Ring Gear

3.73 is a fairly common truck ratio, but certainly not the only one offered.

Chevy truck rear end compatibility chart. It has a 12 bolt cover also, it matches the gm corporate 12 bolt. A four door rear end will fit perfect 3.42 posi bigger brakes always a plus and sway bar is a good thing for daily drivers. Discussion starter · #6 · jul 22, 2005.

What 6 lug rearends will swap with a 51 chevy pickup and still have about the same width as the stock rearend that way i can keep everything i currently have on the truck on it. It would lock the rear axle when there was a difference of 100 rpm's between the two rear wheels. One thing i recommend is installing new seals if you replace your rear end with a used one or you my be doing it twice like me, bad shaft seal.

I swaped mine with a 1989 k5 rear end to clear my 24s and i still have. If you have access to. I am completely swapping the rear end of my 2006 silverado 1500.

Gross vehicle weight rating cap (lbs): Gross combined wt rating (lbs): As you noted, if you buy a junkyard axle, you'll need to match gear ratios if your tahoe is 4wd (if it's 2wd, then you can put whatever gear ratio in you want/find).

They have disc brakes and different gear ratios are readily available. Both rear ends are the same gear ratio and both have drum brakes and leaf springs. Suburban, yukon, and tahoe trucks.

Any '73 to '87 gm truck rear end will fit. 4wd rears are around 53 inside of backing plate to backing plate. The truck has the nose of a studebaker and bobbed and narrowed 1970 bed.

80's camaro,firebird and trans am use the same width rear end; In '99 the differential bearing size was increased for more strength. Something tells me you need special ones,i never dicked with the 10b,went straight to a 14b :flipoff2:

The axels were changed to 5 lug, but still have the 30 splines. Now im not 100% sure about the carrier bearings. Will a 4wd 1998 tahoe 1500 rear end fit in a 4wd 2006 silverado 1500?

15 x 6 15 x 7. People swap in 8.5inch carriers to the 99+ 10 bolts all the time. I take it that it isn't this simple?

The '73 to '81 will be the 12 bolt. They are five lug axles though, which is good if you plan on converting to five lug. It was governed, so that it would not lock at speeds above 15 mph.

Spacers ~ adapters ~ wheels/tires. The 10 bolt started in '82. Chevy 12 bolt rear end.

You only need the orange, black and white with black stripe wire to make them work. 2wd rears are around 47 + 1/2 inside of backing plate to backing plate. So im wondering if anyone found a swap that could be used.

Newest [ november 29, 2021 ]. The light is coming on. The 10 bolt had 28 spline axles up to '90, and then it was upgraded to 30 spline axles.

The eaton was much rarer than the standard 14 bolt gm corporate axle, made by. This number is stamped on the right hand side axle tube of your rear end. > bolt pattern details and matching vehicles.

Very important if you go from a 10 to a 11 brake drum 2) open the differential (rear end), take out the old gears, put in the new gears, put differential back together or replace old 4.11 differential with a new one. According to year one tech, the bolt number count is as follows:

With this number, you can tell exactly what components the factory used in the assembly of your rear end. Any of the truck rear ends with the limited slip differential will have the eaton.

Chevy Truck Rear End Interchange Upgrade Chevrolet - Carautoportal

Truck Camper Compatibility Guide

Chevy Truck Rear End Interchange Upgrade Chevrolet - Carautoportal

Rear 10 Bolt Or 12 Bolt To 14 Bolt Swap - Tips And Advice Lugnut4x4

1973 - 1987 Chevy Truck Specs Engines Transmissions Transfer Cases And Rear Ends Gear Ratios - Chucks Chevy Trucks 87 Chevy Truck Chevy Trucks Silverado